14331BTU Swimming Pool Heat Pump for Above-Ground Pools 110V 0.65KW Pool Heater
Posted on September 22, 2023 | By admin
14331 BTU mini pool heat pump for small water volumes is ideal for small above ground pools. We recommend using it in aboveground swimming pools with a volume of less than 2700GAL, with a maximum pool volume of no more than 4000GAL. 8 foot long power cable with standard USA plug, and 3.3 inches water hose connector make it easily install in 15 minutes. Galvanized steel panel casing allows it to work for many years and assimilate with other swimming pool equipment. It’s your perfect heat pump solution for above ground swimming pools, hot tub or spas. Working Requirements: 8 foot long power cable with standard USA plug, and 3.3 inches water hose connector make it easily install in 15 minutes. Heat pump has an energy efficiency of 5.7, and the operating cost is only 1/5 of the electric or gas heating system. The energy-efficient and low-power heat pump allows you to enjoy your swimming time to the fullest. High Efficiency: Allowing fast and easy hookup without professional installation. With innovative flat-tube titanium heat exchanger, the heat exchanging efficiency is 30% higher than spiral tubes. Premium Security: Available with child lock. Advanced protection system with auto electrical-leakage and low-voltage switch, high and low-temperature, and compressor discharge over-high protection. Compressor Rotary type with R410A refrigerant, CE/FCC certificate. Heating performance suitable for 4000GAL swimming pools. Performance at Air 80 ° F, Water Heated to 80 ° F, Relative Humidity 80%. Rated heating capacity: 14331 BTU/hr. Rated input power: 0.65 kW. Rated COP: 5.4 W/W. Rated/maximum current: 7.5/8 A. Suggested water flow rate: 530GPH. Performance at Air 59°F, Water Heated to 78.8°F, Relative Humidity 70%. Heating capacity:2.49 kW(8496 BTU) Power consumption:0.64 kW C. Heating performance suitable for 2650GAL swimming pools. Rated heating capacity: 11800 BTU/hr. Rated COP: 4.5 W/W. Rated/maximum current: 5/6.5 A. Suggested water flow rate: 400-530GPH. Performance at Air 59 ° F, Water Heated to 78.8 ° F, Relative Humidity 70%. Heating capacity: 2.1 kW. Power consumption: 0.64 kW (2184 BTU). Control opening and closing, real-time display of inlet water temperature, and display of fault codes in case of faults. Heating mode:The set value TSETH range of return water temperature is: 59? 95? Cooling mode:Refrigeration return water temperature setting value TSETH range: 44.6? 86? (parameter C7, initial set temperature 73.4?). High exhaust protection:Fault code E3. Low voltage protection:Fault code EL. Water inlet temperature sensing fault:Fault code E1. Exhaust temperature fault:Fault code E4. Rubber anti slip rubber pad? 0.78 Anti Slip Pad can protect your counter from scratches. For the sturdy character, you don’t need. To worry that the sponge holder would slide down when the sink or counter top fill swith water. High Efficiency? – Allowing fast and easy hookup without professional installation. With an innovative flat-tube titanium heat exchanger, the heat exchanging efficiency is 30% higher than spiral tubes. The compressors have obvious advantages in terms of operating heating efficiency throughout the year, especially the heating performance in winter. Widely applicable to various aboveground swimming pools, it can maintain ideal and consistent temperatures. The non corrosive design makes it durable in coastal climates. Images from different perspectives. GTHP035HSPmn Heating capacity(A80.6W80.6): 14331BTU Heating capacity(A56W78.8): 8496BTU Rated power input: 0.65KW Rated current: 7.5A COPat A27/W27:4.5W/W Power supply:110-120V/60Hz/1Ph Noise10m/1m:43dB(A)/52dB(A) Water connection:32or38mm Advised water flow:2m³/h Water proof class:IPX4 Max. Discharge pressure:4.2MPa Min. 1MPa Water pressure drop:15kPa Refrigerant:R410A(0.45kg) GWPvale:2088 CO2 equivalent:0.80tonnes WeightNet/Gross: 21/24kg. Water Hose Connection: ø 32-35 mm. 2X Water pipe fixed connector. Each pump is tested with water and electricity at manufacturing before the sale, so there will be little water, which doesn’t represent it is used. You need to confirm your water pump, and the advised water flow of our mini heat pump is 400530GPH. If the water flow is too fast, there is not enough time for the pump to heat water, causing the outer part to freeze up. If the water flow is not enough, water is not circulating up, which also results in E8 Code and it doesn’t work. When the pump works properly, there is a temperature difference between the fan outlet and the back air inlet, and also a temperature difference between the water inlet and the outlet. If you want your pool’s temperature to rise quickly, having a solar cover covering the pool at night is helpful. It is helpful to take some photos or videos when you have any usage issues. The high-performance, energy-efficient 14331 BTU Heat Pump quietly and economically maintains ideal water temperature at all times. Ideal for coastal environments. Corrosion-resistant design is equipped with a unique Ultra Gold evaporator fin and titanium heat exchanger for extreme equipment durability. Its compact design allows for easy installation and service on new or existing pools. HeatPro is a great way to extend your swim season.